Last updated: November 7, 2026
Of all the things that can spoil a long motorcycle trip, a neglected chain is among the easiest to avoid and the most annoying to ignore. I learned this the hard way early on, when a chain I had not bothered to check went dry, went noisy and finally wore a sprocket into a hooked shape, leaving me stranded in a small town waiting for parts that took days to arrive. Since then the chain has been part of my daily routine, and the good news is that looking after one is simple, cheap and needs no special workshop. This is how I check, clean, lubricate and adjust a chain on the road, and how I decide when it is genuinely finished.
First, the daily check
Every morning, before I load the bike, I spend a moment looking at the chain. I want it to look lightly oiled rather than dry and rusty, with no stiff links that refuse to bend, and I check the tension in the way the handbook specifies - usually by pressing the chain up and down at a point midway between the sprockets and measuring how much it moves. The exact amount of slack varies from bike to bike, so I never copy a number from another machine; I use the figure printed in my own manual and measure it on the side stand or centre stand as instructed. A chain that is too tight strains the gearbox and bearings, while one that is too loose can jump or even come off, so both extremes matter.
Cleaning makes the lubrication work
Oil on top of grit does more harm than good, because it turns into a grinding paste that wears everything faster. On a long trip I clean the chain roughly every few hundred miles, more often on wet or dusty roads. A proper chain cleaner and a soft brush work well, and I turn the rear wheel by hand to work around the whole length, wiping off the old grease and the road muck with a rag until it comes away clean. I am careful never to use a high-pressure spray aimed straight at the chain, because it can force water past the seals and wash the grease out from inside, which quietly shortens the life of an O-ring chain. Once it is clean and dry, I apply the lubricant.
Lubricating the right way
There is a small knack to oiling a chain that is worth getting right. I spray or drip the lube onto the inside of the lower run while slowly turning the wheel, so that the movement carries it onto the sprockets and works it into the rollers and links, rather than flinging it all over the rear wheel. I give the whole chain a light, even coat and then leave it to soak for a few minutes, ideally after a ride when the chain is warm, because warm metal takes the lubricant better. I wipe off the excess, since a chain dripping with oil simply attracts more dirt. A little and often beats a heavy coat once in a while, and I always carry a small can in the pannier.
Adjusting the slack
When the chain has stretched beyond the allowed slack, it needs adjusting, and this is a straightforward job I do myself rather than hunting for a shop. With the bike secured, I loosen the rear axle nut and then turn the adjuster bolts on each side by small, equal amounts, watching the index marks so that the wheel stays straight and the sprockets line up. Keeping both sides even is the part that matters; a misaligned wheel wears the chain and sprockets fast and can make the bike feel odd. I tighten the axle back to the correct torque, re-check the slack at the same point, and confirm the chain moves smoothly through its full travel. If the adjusters are already near their limit and the chain is still loose, that is telling me something different.
Knowing when a chain is worn out
Chains do not only get loose, they wear, and adjustment cannot fix that. I check for wear by pulling a few links away from the rear sprocket; if they lift well clear of the teeth, or the sprocket teeth look hooked and pointed rather than evenly shaped, the chain is past its useful life. Stiff links, persistent rust and a chain that will not hold its adjustment are the other clear signs. A chain and sprockets are best replaced as a set, because fitting a new chain to worn sprockets just wears it out quickly. I would rather plan that replacement in a city with parts available than discover it on a remote road, and a good shop can fit it quickly if I do not have the tools. A chain that lets go without warning is a genuine breakdown, and it can lock the rear wheel or whip into the cases, so treating the daily check as a habit rather than a chore is a cheap way to avoid a nasty moment. I also keep a note of the sprocket part numbers before a long trip, so if a replacement is needed I can source the right one quickly instead of hunting around with a bike already in pieces.
The paperwork side
As with any foreign motorcycle, entry is handled through a licensed travel agency; individuals cannot clear customs on their own. The temporary plate is valid for 3 months, and the insurance is arranged before entry at the actual cost. For the customs guarantee, with our surety in place the rider only pays 10,000 RMB into the corporate account, arriving 3 days before entry and refunded in full within 3-5 working days after the bike leaves. The vehicle inspection fee is around 200 RMB for every bike. Right-hand-drive machines are accepted at every port on the same terms as left-hand-drive with no surcharge.
If you want help putting together a simple chain-care kit for your trip, or advice on whether your current chain is likely to last the route, send over the details and I will tell you plainly what I think.
Ready to plan your ride into China?
Customs declaration, temporary plate, temporary licence and guarantee - handled for you end to end. Ride across the border on arrival day and keep your energy for the road.
WeChat / WhatsApp: +86 13759155671 · Email: [email protected]
Contact Us Now