Motorcycle riding in China

Last updated: November 7, 2026

When a rider tells me they are sore after a few days on the road, the first thing I ask about is rarely the seat, because more often than not the real culprit is the suspension, or rather the fact that it is still set up for someone else. A bike leaves the factory on a compromise setting aimed at an average rider, and the moment you add a loaded tour - panniers, a tank bag, perhaps a passenger - that compromise no longer matches the weight it is carrying. The good news is that you do not need to be a racer or a mechanic to make a touring bike ride far more comfortably. A few sensible adjustments and a bit of understanding will sort most of it, and this is how I go about it.

Start with the basics: sag and preload

The foundation of suspension is how much it compresses under the bike's weight, and the adjustment that controls this is the preload. If the rear squats too far once you and the luggage are on board, the bike sits low, the steering feels vague and it runs out of travel over bumps, so I add preload to bring it back into its proper range. If it feels harsh and skips over small ridges, there may be too much. I do not chase a precise figure on a tour; I set it so the bike sits level when loaded and uses its travel without bottoming out. Many adventure bikes have a simple collar or a hydraulic knob for this, and a few minutes at the start of the trip is all it takes.

Rebound controls how it comes back

Once the preload is sensible, the rebound is the adjustment that makes the biggest difference to how a bike feels over a series of bumps. Rebound is simply how quickly the suspension extends again after compressing. Too fast and the bike bounces and feels skittish, pogoing over successive ridges; too slow and it does not recover in time, so it packs down and feels wallowy over the next bump. I set it by finding a rough stretch, riding it at a steady speed and changing the adjuster a click or two at a time, aiming for the bike to settle after a bump rather than bounce or stay depressed. Small changes are the secret; winding the adjusters all the way to either end rarely helps.

Load changes everything, so adjust when the load changes

The setting that works for a solo rider with light luggage will not be right for a fully loaded two-up tour, and I treat those as genuinely different setups. When I carry a passenger or heavy luggage, I add preload to support the extra weight and check the headlight aim, because a loaded rear can lift the beam and dazzle oncoming traffic. I also keep an eye on tyre pressure, since it works hand in hand with the suspension; the correct pressures for the load give the tyres their proper shape and grip, and no amount of suspension tuning will rescue a badly under-inflated tyre. I check pressures cold and follow the bike's load table rather than running a single number all trip.

What to leave alone, and when to find a shop

There is a sensible limit to what I adjust at the roadside. Preload and, on better-equipped bikes, the external rebound and compression knobs are fair game and easily reversible, but anything that needs the forks stripped, oil changed or internal parts altered is a job for a professional, not a hotel car park. If the forks are leaking oil, the bike creaks or knocks over bumps, or the adjustments make no difference no matter where they sit, that points to a worn or damaged unit rather than a setting problem, and a good shop can inspect and service it. I would rather have that checked before a long remote leg than discover it far from help. A suspension that bottoms out or behaves unpredictably mid-corner is not merely uncomfortable; it can take the grip away when you are already leaning and contribute to an accident, so a strange noise or a damp fork seal is something I get looked at rather than riding on and hoping. The inspection takes little time and the peace of mind is worth it.

Comfort is the whole point

It is easy to treat suspension as a black box and put up with a harsh or wallowy ride, but getting it roughly right transforms a long tour, reducing fatigue and leaving me fresh enough to actually enjoy the roads rather than just endure them. My approach is simple: set the preload for the actual loaded weight, tune the rebound a click at a time until the bike settles, match the tyre pressures to the load, and leave the internals to a mechanic. Do that and you will arrive at the end of a long day far less battered than you would believe. It is one of those small, unglamorous jobs that quietly makes the whole trip better.

The paperwork side

As with any foreign motorcycle, entry is handled through a licensed travel agency; individuals cannot clear customs on their own. The temporary plate is valid for 3 months, and the insurance is arranged before entry at the actual cost. For the customs guarantee, with our surety in place the rider only pays 10,000 RMB into the corporate account, arriving 3 days before entry and refunded in full within 3-5 working days after the bike leaves. The vehicle inspection fee is around 200 RMB for every bike. Right-hand-drive machines are accepted at every port on the same terms as left-hand-drive with no surcharge.

If you want help working out a starting suspension setting for your particular bike and the load you plan to carry, send over the model and the details and I will suggest where to begin.

Zara
Yunnan Province International Travel Agency (Group) Co., Ltd
WeChat / WhatsApp: +86 13759155671
WeChat ID: qxzj7557
Email: [email protected]
Back to All Guides

Ready to plan your ride into China?

Customs declaration, temporary plate, temporary licence and guarantee - handled for you end to end. Ride across the border on arrival day and keep your energy for the road.

WeChat / WhatsApp: +86 13759155671 · Email: [email protected]

Contact Us Now